PC1616/PC1832/PC1864 v4.6 NA. Installation Guide. WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability the manufacturer. The entire manual should be read carefully. • PowerSeries PC1616/PC1832/PC1864 version 4.1 Installation Guide Note to Installer:Center pages contain important end user information. Leave with End User. WARNING: This manual contains information on limitations regarding product use and function and infor- mation on the limitations as to liability the manufacturer. The entire manual should be carefully read. • Table of Contents Section Description Page Installation & Wiring.. 1 Keybus Wiring..2 Zone Wiring.. 2 Zone Expanders..2 Bell Wiring..2 AUX Power Wiring.. 4 PGM Wiring.. 4 Telephone Line Wiring..4 Ground..4 Battery..4 1.10 AC Wiring.. • PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com. All necessary information required to meet UL Listing requirements is included in this document. • 1.4 Bell Wiring These terminals supply 700mA of current at 12VDC for commercial installations and 11.1-12.6 VDC for residential installations (e.g.DSC SD-15 WULF). To comply with NFPA 72 Temporal Three Pattern requirements: Program Section [013] Opt [8] ON. NOTE: Steady, Pulsed alarms are also supported. • 12V / 7 AHr 12V / 7 AHr To EGND BLACK Terminal 16.5V /40VA DSC Model BD7-12 NON-POWER LIMITED or equivalent Battery StandbyTime: 24Hrs min. FUSE WARNING: Incorrect connections may result in PTC failure or improper operation. Power standby. ULC Commercial Battery capacity will deteriorate with Transformer. Burglary and Fire monitoring installa- age and number of charge/discharge Use DSC PTD 1640U tions require 24 Hr. Power standby. Replace every 3-5 years. Pc1832 User Manual PdfFor Canadian Installa- tions. • Section 2: User Commands Section 2: User Commands Any system keypad can be used to program or perform any keypad command. LED keypads use status and zone indicator lights to represent alarm functions and status. The LCD keypad displays the description and status indicator lights represent alarm functions and status. This section describes basic keypad commands. • PowerSeries - PC1616/PC1832/PC1864 [ ][2] Trouble Display Refer to Appendix D – Trouble Conditions, for troubleshooting assistance and a detailed description of all trouble conditions. [ ][3] Alarm Memory Display The Memory light will be ON if an alarm occurred during the last armed period. Press [ ][3]. The Memory light will flash and the keypad will display the zones that went into alarm. • Section 2: User Commands [ ][6] – User Functions Press [ ][6] followed by the Master Code, then press the number corresponding to the following functions. ![]() Pc1832 Installation Manual PdfProgram Time and Date: Enter the time and date using the following format [HH:MM] [MM/DD/YY]. Bosch gsr 10 8-2-li manual. Program the time using military standard (e.g., 8:00 pm = 20:00 hours). • PC1616/1832/1864 Reference Manual for a complete description of all programmable features. 3.1 How to Program: DSC recommends filling in the Programming Worksheet with the required programming information before programming the system. This will reduce the time required to program and will help eliminate errors. • Section 3: Programming 3.5 Viewing Programming LED and LCD5501Z Keypads Any programming section can be viewed from an LED or LCD5501Z keypad. When a programming section is entered, the keypad will immediately display the first digit of information pro- grammed in that section.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |